DESIGNJET T1300 SERVICE MANUAL PDF

Print from a computer using the Embedded Web Server or HP Utility (T series). free Web service makes it easy to access and print large-format documents . It is possible to assign a manual IPv6 address to the printer, using the front. This Service Manual contains information necessary to test, calibrate, maintain and service the following: HP Designjet T 24inch; HP Designjet T 44inch;. HP DesignJet T and T Printer Series. Using your The only warranties for HP products and services are set .. Web Services manual configuration.

Author: Mazubar Gardalkis
Country: Sudan
Language: English (Spanish)
Genre: Travel
Published (Last): 11 October 2008
Pages: 112
PDF File Size: 7.53 Mb
ePub File Size: 8.37 Mb
ISBN: 577-8-32300-812-8
Downloads: 31385
Price: Free* [*Free Regsitration Required]
Uploader: Akisar

Electronics Module Test The purpose and scope of this test is different when compared to some of the other HP Designjet products of the same platform. When the Pinchwheel Alignment Tool is fully expanded, the is properly aligned.

Otherwise, the product confirms success as follows.

Replace with a new one if necessary. Remove the Scanner Position Sensor. Rotate the Drop Detector vertically to gain access to the two screws that secure the Right Starwheel Lifter. Press on the Service utilities menu option. You are recommended to order the Paper Advance Calibration Kit in models: The connectivity is enabled if YES option is confirmed.

Page 40 Whenever you replace the Printhead, check the empty slots to see if they need cleaning.

HP Service Manual for CRA DesignJet t in eprinter

You can use a roll that is at least mm 24 in wide or a cut sheet that is A2 landscape or larger. The PRS subsystem is designed to move the carriage assembly between two predetermined vertical positions with respect to the plane of the print platen.

Most 10 Related  AKTA BAHAN KAKISAN DAN LETUPAN PDF

Table Of Contents Roll Covers Use a flat end screw driver as a lever to remove the part. Disconnect the Scanner Position Sensor from the cable.

HP DESIGNJET T EPRINTER SERIES SERVICE MANUAL Pdf Download.

The one at the start of the CIS is a bit smaller than the one at the end, it makes a black point, unlike the end which makes a Black and a White point. Make sure all the ferrites are removed. Press on the Printhead Designnjet icon and the following screen is displayed. Page 57 Problem Description: Lift the Starwheel Motor out of the product. Disconnect from Interconnect Board the cables: Page 33 To insert a new printhead first remove the orange protective caps.

The product performs a series of movements to test the primer.

HP Designjet T790 / T1300 / T2300 series. Service Manual

Power Cable from Main. Check the condition and connections of the Scanner Power cable, if necessary replace the cable. Rotate the Out Of Paper Sensor cover approximately 45 degrees. CH Engine Cables Kit. Page 28 To change an ink cartridge there are two methods, the first is shown below by using the ink tab, the second method is to access the main menu option refer to the User’s Guide desigjet further details.

Cable Snoopy to Power. Do not loosen or remove the other screws Do not remove the screws circled. Using the Touch Control Panel The front panel is located on the front right of the printer.

Most 10 Related  CTHULHUTECH CORE PDF

Disconnect the cable connector as shown. Make sure to snap the bumper on to both parts shown. Ink Setup failure Corrective action: The Toolkit contains the following tools: Installation without encoder sensor adjustment Use the following procedure to install and adjust a new Media Advance Drive. Page Hold the calibration sheet from both sides and place it facing the arrow in the centre of the sheet in front of the Page icon present on the input tray of the scanner.

Page The product performs a series of movements numbered from 1 to There is a setting available that enables you to decrease the resolution for each print mode to dpi.

Left Cover on page CQ Rear Cover T Start the product and calibrate the drop detector. Remove the screw on the left side g1300 the converger at the rear of the product.

Power cable of the Scanner is failing Manuzl action: The Touch Control Panel displays the sleep mode status. Carefully position the Media Advance Drive in the product. This page requires Javascript. Insert the slider on to the center support and tighten the T—15 screw indicated A. Close the Carriage Cover. Page 69 A firmware upgrade will not always solve the problem.